Today was both rewarding and frustrating. The plan was to come out this morning and fire up the engine. Only she would not start. Cranked and cranked and cranked but no fire. Not even a sputter. Pulled the plugs and took a look. of course they were fouled. Cleaned them, but them back in and nothing. At this point I was ready to drag it to the mechanic and say I was done. However, after lunch came back to it and got some help from my daughter so that I could pull the plugs and see if they were sparking. Well they were. So, now what is going on. We have a half tank of gas and spark so next thing to check was gas flow the carb. However, before doing that I noticed that the choke plate was not closed all the way. So, while crankeing I pushed the choke plate all the way closed. The motor fired right up !!! Wow. Everything worked fine. Prop engaged correctly and there were NO LEAKS wow. we might actually have this figured out. I properly drained the cooling system in prep for tonights sub freezing plunge. After about 4 hours I decided to see if the motor would start again hopefully more easily. I also purchased some B-12 Chemtool to clean the throats and the shafts on the carb. So I hooked the cooling system back up and turned on the water flow and turned the key. She fired right up !!! Everything checked ok so I shut down and drained the system again.
Installed the boarding ladder over the transom. Next step is to install the tow rings on the back. Then have to seal up the stern drive bellows.
Saturday, January 3, 2009
Friday, January 2, 2009
It Runs Again
Well I got the last of the engine mount bolts installed. Was surprised to find how much one side had fallen. Had to bring it up using a drift pin. Filled holes with J.B.Weld prior to installing the bolts so they should be in their good and well sealed.
Engine took some cranking to get started. After it got started it ran just fine and restarted without any problems. Had to let it warm up before it would pickup the prop. Not sure what is up with that. Also had a couple of minor leaks in the new exhaust plumbing. A couple of tweaks on the clamps and that seemd to clear up the problem.
Planning on starting it again tomorrow. Hopefully it will light right up with out any problems.
Engine took some cranking to get started. After it got started it ran just fine and restarted without any problems. Had to let it warm up before it would pickup the prop. Not sure what is up with that. Also had a couple of minor leaks in the new exhaust plumbing. A couple of tweaks on the clamps and that seemd to clear up the problem.
Planning on starting it again tomorrow. Hopefully it will light right up with out any problems.
Thursday, January 1, 2009
Transom Is In !!!
The transom is installed. All of the bolts are installed. All that is left to do is install the aft engine mount bolts. Completed the installation of the exhaust riser and the front plate on the exhaust manifold. Once the gasket sealer sets up its time to flush the system and make sure there are no leaks.
Wednesday, December 31, 2008
Continued working on the transom. All parts are cut and checked. Just need the weather to get up above 50 again so that the glue will work.
Reinstalled the exhaust riser and worked out the exhaust connection. Photos coming once everything is installed.
Scraped the remaining carpet pieces off of the right side of the cockpit area.
Reinstalled the exhaust riser and worked out the exhaust connection. Photos coming once everything is installed.
Scraped the remaining carpet pieces off of the right side of the cockpit area.
Sunday, December 28, 2008
Monday, December 8, 2008
12-7-2008 Transom Goes Back In
Well I got all the wood pieces for the transom back up in the boat. All the parts fit and the long piece across the stern I thought would give me fits but it slid right in with no problem. Picked up some stainless screws to put it all back together with. I am going to use a polyurethane based glue to put it all together with. Figure because it is going to be screwed through out that the polyurethane should work good.
Photos coming soon.
Photos coming soon.
Friday, November 7, 2008
11-7-2008 Another Catchup Post
Ok, the new helm is installed with new gages. The wheel is back in and all seems to be working. Started the motor and all the gages come to life and seem to be working just fine. All the parts for the transom are built and in the process of final fitting. Started cleaning up all of the other stuff I had ripped out to see what is usable and what needs to be replaced.
Not much hope that it is going to see water this year. Hopefully in the spring next year.
Not much hope that it is going to see water this year. Hopefully in the spring next year.
Subscribe to:
Posts (Atom)